ARAV RX logo
JAEN
Talk to us about your site

ARAV RX SERIES

Remote control and autonomy for the excavators you already own

ARAV RX is a retrofit kit that lets you operate a hydraulic excavator from up to approx. 1,000 km away and automate repetitive work such as hopper and crusher feeding. It installs without modifying the hydraulic system and works across makes, including Cat, Komatsu, Hitachi, Kobelco and Sumitomo.

ARAV RX tablet showing the autonomous work plan

What ARAV RX does

RX adds three capabilities to an existing excavator. You choose the combination that fits your site, and the machine can still be operated from the cab as before.

Teleoperation

Operate the excavator from a safe location with a game controller, joysticks or a dedicated operator station. Cloud connection over 4G LTE/5G reaches up to approx. 1,000 km; control latency is approx. 0.06 s.*

Remote solution

Autonomous operation

The machine repeats the dig, swing, dump and return cycle on its own to feed hoppers and crushers (approx. 30 s per cycle*). One operator supervises from a tablet and steps in only when needed.

Autonomous solution

Safety stops

Two independent stop systems: a dedicated radio emergency stop that works without the network, and an automatic stop when the link degrades. Beacon lights show the machine state to people nearby.

Safety

* Reference values from ARAV's test environment (recommended network, low load; 0.7 m³ bucket class for the feeding cycle). Actual values vary with the network, machine, site conditions and settings.

Remote operation
from up to 1,000 km away

Ultra-low-latency transmission lets operators far from the site work as if they were sitting in the cab.

Latency
approx. 0.06 sec
Range
approx. 1,000 km

* Reference values measured in ARAV's test environment (recommended network, low load). Actual values vary with the network type, signal conditions and site load.

LiDAR-based autonomy
for repetitive work

The retrofit autonomous system takes over repetitive tasks such as hopper feeding and dump truck loading. LiDAR scans the dig area, so the machine keeps finding material in the pile. It helps with labor shortages and keeps people out of the machine's working area.

Tasks
Feeding / Loading
Cycle time
approx. 30 sec

* Reference value from ARAV's test site (0.7 m³ bucket class, feeding task). Actual values vary with the machine, site conditions and settings.

Where RX fits

RX is built for sites where excavators repeat the same task for long periods, or where it is dangerous for people to be near the machine.

Quarries and aggregates

Quarries and aggregates

Feeding raw rock into primary crushers, and screening.

Recycling and plants

Recycling and plants

Feeding work at plants and recycling facilities, such as concrete rubble screening.

Earthworks

Earthworks

Surplus soil yards, river dredging with screening, and soil stabilization plants.

Hazardous sites

Hazardous sites

Disaster recovery, erosion-control works, tunnels and dams, operated from a safe distance.

Works across makes: universal retrofit

Real sites rarely run a single brand. ARAV's core technology connects to hydraulic excavators without intruding on the machine, regardless of make or model. The main targets are excavators of the 13 t class (0.5 m³ bucket, JIS) and above with electronic joystick controls; mini excavators are not supported. Examples of supported models:

CAT315
CAT374

Electronic joystick

CAT313, CAT315, CAT320-GC, CAT323, CAT325, CAT326, CAT330, CAT336, CAT340, CAT345-GC, CAT352, CAT374, CAT395, etc.

Recommended
CAT320
PC200

Electronic joystick
+ built-in ICT sensors

CAT320-07, PC200i-12, etc.

ZX200
SK200-10
SH200-8

Pilot hydraulic

ZX200-7, SK200-10, SH200-8, etc. (please ask us for details)

Model names are as sold in Japan, and supported models may change without notice. Send us the make, model and year of your machines and we will check compatibility. One operator device can control machines of different makes, so mixed fleets can be run from the same seat.

Check your machines

Agreement with Hitachi Construction Machinery on RBT Core Connect

ARAV has agreed with Hitachi Construction Machinery Co., Ltd. to apply “RBT Core Connect”, Hitachi's interface for remote and autonomous operation, to ARAV's automation system. This allows smooth and safe automation of the 20-tonne class ZX200A-7 and the 30-tonne class ZX330A-7 through a manufacturer-approved interface.

Hitachi Construction Machinery Co., Ltd. plans to change its name to LANDCROS Co., Ltd. on April 1, 2027.

Hitachi RBT Core Connect with ARAV

Why ARAV

Excavators retrofitted with ARAV RX

Retrofit, and move it to another machine

No new machine is needed. The system can be removed from one make and reinstalled on another (for example from Cat to Komatsu), so you keep using it over the long term.

* Reinstallation is carried out by ARAV and is charged separately, with its own lead time.

Independent, so priced competitively

ARAV is not tied to any machine manufacturer. Retrofitting instead of buying new machines keeps costs well below manufacturer-installed systems, and the system can move to other makes.

ARAV engineers assembling hardware

Designed and built in-house in Japan

ARAV designs both the hardware and the software, from the on-machine controller and actuators to the remote-operation software and the operator station.

Installing RX in the cab

Back to manual operation at any time

RX connects electrically and with a patent-pending actuator mount, without touching the hydraulic circuit. If anything goes wrong, an operator can sit in the cab and run the machine as usual.

SAFETY SYSTEM

Two independent stop systems

Remote and autonomous operation need safety mechanisms that react immediately to lost communication or anything unexpected. The RX series has two independent stop systems so the machine can always be brought to a stop.

Radio emergency stop

A dedicated radio link, separate from Wi-Fi and LTE

The site supervisor carries a handheld emergency stop unit that sends the stop signal over a dedicated low-power radio link. The handheld unit is used within line of sight of the machine. Because it is completely independent of Wi-Fi, LTE and other networks, the emergency stop works even when the network fails.

0.15s*

Response time to stop

Two-way

Communication

  • Independent of the network — works during network outages
  • Hydraulic lock can be engaged from the handheld unit
  • Automatic stop if the machine leaves the handheld unit's range
  • The handheld unit must be kept within line of sight of the machine

In Japan, the unit uses the 429 MHz / 920 MHz specified low-power radio bands. Radio regulations differ by country, so please ask us about use in your country.

Automatic stop on network faults

Communication between devices is monitored continuously

The link between the operator's device and the machine is monitored in real time. If the system detects rising latency, packet loss or other faults, it brings the machine to a safe stop automatically, before the operator even notices.

2s*

From fault detection to stop decision

Always on

Monitoring

  • Stop thresholds can be customized
  • Secure communication with authenticated, encrypted MQTT
  • Mesh Wi-Fi plus fiber, Starlink or 5G

Status visible on site

The machine carries a beacon light (red, yellow, green) that shows workers nearby whether it is running autonomously, on standby or stopped because of a fault. IP radios are used for voice communication on site, so the site supervisor and the person managing autonomous operation can talk at all times.

* Response and fault-detection times are reference values from ARAV's test environment and vary with the network, site load and settings. Operating the RX series requires the customer to ensure site safety, including work zoning, supervision and emergency stop arrangements. See the Safety page for details.

How a deployment works

01
Requirements and detailed consultation

We review your site conditions, existing machines, communication environment and operating setup, then agree on the equipment specification, installation scope and the schedule to start of operation. If needed, we run a demonstration on a test machine. Depending on the conditions, demonstrations may be charged separately.

2-4 weeks / online and on site
02
Installing the remote/autonomous system (hardware)

The system is installed at ARAV's assembly workshop or on site. It is a retrofit that does not touch the hydraulic system, so the machine can be returned to its original state. An in-house inspection checks the sensors, communication and safety functions.

1-2 weeks / workshop or on site
03
Equipment purchase and software agreements

After installation, we sign a purchase agreement for the equipment (remote-operation or automation unit) and a subscription agreement (monthly or annual) for the remote/autonomous operation application. Price, payment terms and maintenance scope follow what was agreed in the consultation.

Equipment: purchase / Software: subscription (monthly or annual)
04
Go-live and periodic maintenance

The equipped machine is delivered and operation begins. The first year includes periodic maintenance support and operator training. Maintenance from the second year is agreed based on the operating record. After reviewing operating conditions and the site setup, we may not be able to accept every project.

First-year support included / from year 2 by agreement

These steps describe how projects run in Japan. For sites outside Japan, installation, operator training and maintenance arrangements are discussed with each customer before the project starts.

Common questions

Which machines are supported?

Mainly excavators of the 13 t class and above with electronic joysticks, across makes. Mini excavators are not supported. See the model examples above.

How much does it cost?

It depends on the machines, site conditions and package. Contact us for a quote.

Can we try it first?

Demonstrations can be arranged at ARAV's facility in Japan by appointment. During the consultation phase, a demonstration on a test machine can also be arranged; it may be charged depending on the conditions.

We are outside Japan. Can we work with ARAV?

Yes. Tell us your country, site type, machines and tasks. Export, local support and warranty arrangements are discussed with each customer.

All questions

Start building the site of the future today.

Tell us about your machines and the work you want to make remote or autonomous. We will get back to you by email.

Contact us
Download the ARAV overview (PDF)

Evaluating ARAV RX for your site?

Contact us

Already using ARAV RX?

Contact us

Interested in becoming a distributor?

Partner program