Frequently asked questions
Questions we often hear before a project starts.
If your question is not answered here, please use the contact form.
Q.We are outside Japan. Can we discuss a project with ARAV?
A.
Yes. Please use the contact form and tell us your country, the type of site (for example mine, quarry, steel plant, waste or port), the make, model and year of your excavators, and the tasks you would like to run remotely or autonomously. Export, local support and warranty arrangements are discussed with each customer.
Q.Do you support overseas versions of machines and large mining excavators?
A.
Our track record is with machines sold in Japan. Regional versions of the same models and large mining-class excavators are checked model by model. Send us the make, model and year of your machines.
Q.Who handles installation, training, maintenance and spare parts outside Japan?
A.
This is discussed and agreed with each customer.
Q.What about export terms, warranty and local certifications such as CE or FCC?
A.
Export terms, warranty and compliance with the regulations of your country, including the wireless emergency stop, are confirmed for each project.
Q.Can we run a demo or pilot at our site outside Japan?
A.
Please contact us to discuss a demo or pilot at your site.
Q.Will RX work with our local mobile networks and power supply?
A.
Mobile networks and the power supply for the operator station are checked against the conditions at your site.
Q.Can RX make a site completely unmanned?
A.
No. On-site safety management and daily machine inspections are still required, so installing RX alone does not make a site fully unmanned. However, reviewing how inspections, refueling and work plans are organized when you introduce RX can improve the efficiency of the whole site.
Please also check the latest safety guidelines that apply in your country.
Q.Where is RX being used today?
A.
It is used at sites where work continues for a certain period and a communication environment can be set up, such as unmanned construction zones in landslide-countermeasure works in Japan.
Q.Can RX be used on a machine that only loads and stays in one place?
A.
Depending on site conditions, yes. A site visit is needed for the final decision, in particular to check that the required communication environment can be set up.
Q.How much latency is there in remote operation?
A.
It varies with communication conditions, but normally stays within a range that does not hinder operation. You can try the operating feel at ARAV's demonstration facility in Japan.
Q.How much bandwidth is needed on site?
A.
We propose the best communication setup for your site and use case. In general, we recommend Wi-Fi equipment rated for outdoor use.
Q.Does RX work with commercial (carrier) 5G?
A.
RX Pro supports commercial 5G. Compatibility with mobile networks outside Japan needs to be checked for each country.
Q.Does remote operation feel different from sitting in the cab?
A.
Functions such as motion haptics and sound feedback are designed to bring the experience close to operating from the cab.
How it feels varies from person to person.
Q.Which machines does RX support?
A.
The main targets are hydraulic excavators of the 13 t class (0.5 m³ bucket, JIS) and above with electronic joystick controls. Standard backhoe configurations are the base, and some special-purpose configurations (magnet, elevating cab, grapple) are also supported. For pilot-hydraulic machines, please ask us for details.
■ Electronic joystick + built-in ICT sensors
CAT320-07, PC200i-12, etc.
■ Electronic joystick
CAT313, CAT315, CAT320-GC, CAT323, CAT325, CAT326, CAT330, CAT336, CAT340, CAT345-GC, CAT352, CAT374, CAT395, etc.
■ Pilot hydraulic
ZX200-7, SK200-10, SH200-8, etc.
Model names are as sold in Japan, and supported models may change without notice. Send us the make, model and year of your machines and we will check them.
Q.Can machines we already own be converted for RX?
A.
Yes. Conversion requires modification work, done either at ARAV's workshop or on site.
Q.Do you support mini excavators?
A.
Not at present.
Q.Will hardware stay compatible after a model change?
A.
The RX series is updated continuously to add functions and improve performance. If a model change happens along the way, hardware compatibility may not be maintained.
Q.Can RX detect oil leaks?
A.
Depending on where the leak is, it may be visible in the camera feed, but RX has no dedicated function for detecting oil leaks automatically. We recommend covering this through operations, such as pre-start checks and regular inspections by the site manager.
Please also follow the safety guidelines in your country and the manufacturer's inspection requirements.
Q.Can RX be used in bad weather (snow, storms, fog, heat)?
A.
Not in conditions where safe judgment would be difficult even from the cab, such as whiteouts, dense fog or work in darkness.
Q.Does RX support crane (lifting) work?
A.
No. For crane work, operate the machine's lifting function from the cab.
Q.Can RX connect remotely to other manufacturers' systems?
A.
Remote connection is possible (quoted separately).
Q.Can RX work with machine guidance/control (MG/MC) or collision mitigation systems?
A.
Partly. In some cases they can be used at the same time. However, changing their settings from the remote operator seat is limited (quoted separately).
Q.Can RX be installed on custom-built machines?
A.
A preliminary survey is required. Some customizations cannot be supported, so please contact us with details.
Q.How much does RX cost?
A.
It depends on the machines, site conditions and package, so please contact us for a quote.
Q.Can we purchase the equipment?
A.
Yes. The remote-operation and automation equipment is sold under a purchase agreement, and the dedicated software is provided under a monthly or annual subscription. Annual prepayment of the subscription is also available.
Q.Are repairs included in the service fee?
A.
Repairs to the operator station are included in the fee, although damage caused by the customer may be excluded. Failures of the on-machine equipment purchased at the start are charged separately.
Q.Is there a cost when the contract ends?
A.
Yes. The station and equipment need to be removed, so a removal cost applies. Restoring operator rooms or machines prepared by the customer is charged separately.
Q.Can the contract be ended early?
A.
Yes, although a cancellation fee may apply depending on how long the service has been used.
Q.What safety measures does RX follow?
A.
In Japan, RX complies with the “Safety Rules for Autonomous Construction Ver. 1.0” issued by the Ministry of Land, Infrastructure, Transport and Tourism (MLIT) in March 2024. Outside Japan, the rules that apply in the country of operation must be followed.
MLIT Safety Rules for Autonomous Construction Ver. 1.0 (PDF, Japanese)
Q.Who is responsible if an accident happens during remote or autonomous work?
A.
It is discussed case by case depending on the circumstances, mainly from the following points of view:
- Whether measures based on the safety rules were in place
- How safety was managed when setting up, starting and stopping autonomous work
- Whether the system was used in environments or ways beyond its specifications
- Whether modifications not described in the manual had been made
- Whether it can be confirmed that the system became uncontrollable under normal use
- Whether the emergency stop worked correctly and was used in an appropriate environment
Q.How far does the emergency stop reach?
A.
Basically within a 20 m radius. From a site office or other places far from the machine, the stop signal may not reach it reliably. Make sure that someone near the machine, such as the operator of another machine or the foreman, can stop it.
Q.What should site workers be told in safety training?
A.
Explain in advance, and enforce, that nobody enters the working area during autonomous work. If entry is unavoidable, make sure every worker knows who is in charge, and set up procedures for stopping the machine and entering the area safely.
Q.Are there laws on remote or unmanned construction machines?
A.
In Japan, there is currently no law specific to remote or unmanned construction machines; MLIT is working on standard safety rules through a council on automation of construction machinery. The RX series conforms to the Japanese Industrial Standard (JIS) for the safe operation of radio-controlled excavators. Requirements in other countries differ, so please check the regulations where you operate.
New regulations may require us to change or suspend the service without notice.
Q.What qualifications do operators need?
A.
In Japan, operators need the same qualifications as for operating the machine conventionally, as with radio-controlled excavators. Outside Japan, follow the requirements of the country of operation.
Q.Can we try remote operation?
A.
Yes, at ARAV's demonstration facility in Japan, by appointment. Operating the machine requires the same qualifications as normal machine operation.
Q.Is rental available?
A.
Rental may be possible depending on the conditions. Please contact us for details.
Q.Is there a support desk?
A.
Yes, ARAV has a dedicated service desk, and we explain how to use it together with the operating procedures at deployment. For sites outside Japan, the support arrangement is agreed before the project starts.