RX Pro
One operator supervising several machines hundreds of kilometers away
Operate machines hundreds of kilometers away from an immersive, dedicated operator station. Combined with the low-latency GMSL camera (approx. 0.3 s latency *1), it feels as if you were on site. With advanced functions such as automatic loading, machine control (MG/MC) and virtual walls (some to be released in stages), one operator supervises several machines running autonomously and switches to remote control of one machine only when needed (*2). *1 Latency figures are reference values from ARAV's test environment (recommended network, low load) and vary with the network and site conditions. *2 In line with the June 2026 interim report of Japan's Ministry of Health, Labour and Welfare on unmanned machine operation, one person remotely operates only one machine at a time; the other machines run autonomously under supervision.



One operator supervises several autonomous machines and takes over one when needed
Built on the immersive operator station, RX Pro integrates advanced autonomous functions such as automatic loading, machine control and virtual walls. It is the top remote-operation package, designed so that work that used to need three people can be handled by one.* (*An estimate based on assumptions about the task, site size, scope of automation and supervision setup; actual results vary with site conditions. One machine at a time is operated remotely while the others run autonomously under supervision. See the Safety page for details.)
Dedicated operator station
An operator desk with multiple monitors. The environment is close to the real machine, helping operators stay focused through long shifts.
Multi-machine operation
One operator supervises several autonomous machines and switches to remote control of one when needed. Combined with automatic loading, work that used to need three people can be handled by one (depending on site conditions and the supervision setup).
Machine guidance and control (MG/MC)
Support for machine guidance and machine control is planned, enabling precise remote work based on 3D design data.
Remote operation
from up to 1,000 km away
Ultra-low-latency transmission lets operators far from the site work as if they were sitting in the cab.
* Reference values measured in ARAV's test environment (recommended network, low load). Actual values vary with the network type, signal conditions and site load.
LiDAR-based autonomy
for repetitive work
The retrofit autonomous system takes over repetitive tasks such as hopper feeding and dump truck loading. LiDAR scans the dig area, so the machine keeps finding material in the pile. It helps with labor shortages and keeps people out of the machine's working area.
* Reference value from ARAV's test site (0.7 m³ bucket class, feeding task). Actual values vary with the machine, site conditions and settings.

Autonomy
Automatic loading, machine control and virtual walls
RX Pro inherits the automatic hopper feeding and automatic loading (planned) of RX Standard and extends the targets and scale. In addition to on-site crawler carriers, automatic loading of road-going dump trucks is planned, running the dig, load and wait cycle automatically. Machine control support (MG/MC, planned) will enable semi-automatic work based on 3D design data. The virtual wall limits the machine's working range in software to keep it away from nearby structures and hazardous areas. Together, these functions let one operator supervise several autonomous machines and switch to remote control of one machine when needed (following the operating conditions of the Japanese interim report described on the Safety page).
- Automatic loading of dump trucks
- Machine guidance and control (2D/3D MG/MC) planned
- Virtual wall (working-range limit)
- Several machines run by one operator

Cameras
GMSL, dome and PTZ multi-view
An in-cab GMSL camera (720p/30fps, 0.3 s latency) is combined with a front dome camera (720p/30fps, 0.6 s) and an overhead PTZ cloud camera (1080p/30fps, 0.6 s). The low-latency GMSL feed shows fine movements at the bucket tip, while the dome and PTZ cameras give a wide view of the whole site. All three views are shown at once, so the operator works without blind spots.
- In-cab GMSL camera (720p/30fps, 0.3 s latency)
- Front dome camera (720p/30fps, 0.6 s latency)
- Overhead PTZ camera (1080p/30fps, 0.6 s latency)
- Three views on screen at once
* Video latency and resolution are reference values measured in ARAV's test environment (recommended network, low load). They vary with the network type, signal conditions and site load. Stable three-view display assumes the recommended device and bandwidth.

Controls
Intuitive control with a game controller
The excavator can be operated with an off-the-shelf game controller, so no special hardware is needed. The button and stick layout is quick to learn, and operators new to remote work can be productive within a short time. Control latency is approx. 0.06 s, so there is practically no perceptible lag. The operator watches the video on a tablet while operating.
- Works with off-the-shelf game controllers
- Short learning curve, no special training
- Control latency approx. 0.06 s
- Video monitoring on a tablet
* Control latency is a reference value measured in ARAV's test environment (recommended network, low load). Supported controller models and the time operators need to become proficient depend on their experience and site conditions. Please ask us for details.

Controls
Tablet-only operation
In autonomous mode, the machine is run entirely from one tablet. Video monitoring, starting and stopping autonomous work, and adjusting parameters are all done by touch, with no controller or joystick required. The minimal setup makes deployment and operator training simpler.
- Everything on one tablet
- No additional controller required
- Designed for supervising autonomous work
- Minimal equipment to deploy

Controls
Precise control with joysticks
Joysticks optimized for construction machinery come as standard. Lever stroke and resistance are close to the real machine, allowing fine adjustments. Even precision work such as slope finishing or working close to structures can be done without strain, operator fatigue is reduced during long shifts, and you can switch to a game controller depending on the task.
- Joysticks built for construction machinery
- Lever feel close to the real machine
- Suited to precision work such as slope finishing
- Switch between joystick and game controller as needed

Controls
Dedicated operator station
The operator station integrates joysticks and pedals into a desk with multiple monitors. Operators take in a wide field of view in an environment close to the real machine, which improves their judgment and helps prevent unintended contact with machines or structures. It is designed for long shifts and to reduce operator strain.
- Dedicated operator station
- Multiple monitors at once
- Designed for long shifts

Connectivity
Cloud connection (up to approx. 1,000 km)
A cloud connection over the machine's 4G LTE/5G link allows remote operation from up to approx. 1,000 km away. There is no need to set up a cabin near the machine; work can be done from a safe office. A fail-safe brings the machine to a safe stop if communication is lost.
- Cloud connection
- 4G LTE / 5G required at the machine
- Remote operation from up to approx. 1,000 km
- Fail-safe stop on loss of communication
System components
- Industrial PC: runs the autonomous-operation control software
- LiDAR: 3D sensing of the surroundings
- IMU: measures attitude and acceleration
- Encoder: measures the swing angle

SAFETY SYSTEM
Two independent stop systems
Remote and autonomous operation need safety mechanisms that react immediately to lost communication or anything unexpected. The RX series has two independent stop systems so the machine can always be brought to a stop.
Radio emergency stop
A dedicated radio link, separate from Wi-Fi and LTE
The site supervisor carries a handheld emergency stop unit that sends the stop signal over a dedicated low-power radio link. The handheld unit is used within line of sight of the machine. Because it is completely independent of Wi-Fi, LTE and other networks, the emergency stop works even when the network fails.
0.15s*
Response time to stop
Two-way
Communication
- Independent of the network — works during network outages
- Hydraulic lock can be engaged from the handheld unit
- Automatic stop if the machine leaves the handheld unit's range
- The handheld unit must be kept within line of sight of the machine
In Japan, the unit uses the 429 MHz / 920 MHz specified low-power radio bands. Radio regulations differ by country, so please ask us about use in your country.
Automatic stop on network faults
Communication between devices is monitored continuously
The link between the operator's device and the machine is monitored in real time. If the system detects rising latency, packet loss or other faults, it brings the machine to a safe stop automatically, before the operator even notices.
2s*
From fault detection to stop decision
Always on
Monitoring
- Stop thresholds can be customized
- Secure communication with authenticated, encrypted MQTT
- Mesh Wi-Fi plus fiber, Starlink or 5G
Status visible on site
The machine carries a beacon light (red, yellow, green) that shows workers nearby whether it is running autonomously, on standby or stopped because of a fault. IP radios are used for voice communication on site, so the site supervisor and the person managing autonomous operation can talk at all times.
* Response and fault-detection times are reference values from ARAV's test environment and vary with the network, site load and settings. Operating the RX series requires the customer to ensure site safety, including work zoning, supervision and emergency stop arrangements. See the Safety page for details.
Use cases
Where this package is typically used
* The sites shown are typical examples of how the RX series is used. Each deployment is decided with the customer after reviewing site conditions, tasks and the safety management setup, on the premise that the customer is responsible for site safety.

Surplus soil yard
Remote operation at a surplus soil yard on your own premises, combined with automatic feeding and automatic loading for high efficiency.

Disaster recovery
Clearing landslides after earthquakes or heavy rain. Recovery work proceeds quickly while workers stay out of areas at risk of secondary collapse.

Erosion-control dam works
Building check dams in mountain streams exposed to debris flows. Nobody is stationed in the hazard zone; the excavator is operated remotely from a safe area.

Tunnel construction
Work inside tunnels, where rockfall and dust are serious risks. Operators work remotely from a safe office hundreds of kilometers away.

Dam construction
Dam projects with large earthwork volumes and long schedules. Running several machines with one operator helps address chronic labor shortages.

River dredging with screening
Excavating river sediment and feeding it into a screening plant for grading. Combined with automatic hopper feeding, a small crew can keep the plant running continuously.

Quarry primary crusher feeding
Feeding raw rock into the primary crusher at an aggregate quarry. Automating this heavy, hazardous task keeps the crusher fed steadily with fewer people.

Concrete rubble screening
Screening crushed concrete. The operator stays in a safe place away from the dust while automatic feeding keeps throughput stable.

Soil stabilization plant
Feeding the hopper of a self-propelled soil stabilization (mixing) plant. The automatic cycle holds a steady feed rate with a small crew.
Features by package
Compare RX Pro with the other packages
| Feature | RX Entry Type R | RX Entry Type A | RX Standard | RX Pro |
|---|---|---|---|---|
| Teleoperation: typical sites | ||||
| Surplus soil yards | ||||
| Disaster recovery works | - | |||
| Erosion-control (sabo) dam works | - | |||
| Tunnel construction | - | - | - | |
| Dam construction | - | - | - | |
| Controls (latency approx. 0.06 s) | ||||
| Tablet | ||||
| Game controller | - | |||
| Joystick | - | |||
| Operator station | - | - | - | |
| Cameras | ||||
| In-cab GMSL camera (720p/30fps, 0.3 s) | - | |||
| Front dome camera (720p/30fps, 0.6 s) | ||||
| Overhead PTZ cloud camera (1080p/30fps, 0.6 s) | - | |||
| Site requirements | ||||
| 4G LTE / 5G coverage at the machine | - | |||
| Clear line of sight between machine and relay (approx. 20 m) | - | - | - | |
| Site cabin to serve as the base station | - | - | - | |
| Fiber or satellite link at the base station | - | - | - | |
| Machine control (ICT) | ||||
| 2D/3D machine guidance (MG) | - | - | *1 | *1 |
| 2D/3D machine control (MC) | - | - | - | *1 |
| Safety for autonomous operation | ||||
| Virtual wall | - | *1 | *1 | *1 |
| Automatic lever-pattern recognition | - | *1 | *1 | *1 |
| Real-time obstacle detection with LiDAR | - | - | *1 | *1 |
| Connectivity and range | ||||
| Cloud connection (up to approx. 1,000 km) | ||||
| On-premises connection (closed network) | - | - | - | |
| Automatic feeding: typical sites | ||||
| River dredging with screening | - | |||
| Quarry primary crusher feeding | - | |||
| Concrete rubble screening | - | |||
| Soil stabilization (self-propelled mixer hopper) | - | |||
| Automatic loading: targets | ||||
| On-site crawler carriers | - | - | *1 | *1 |
| On-site dump trucks | - | - | *1 | *1 |
| Road-going dump trucks | - | - | *1 | *1 |
| Automatic excavation from BIM/CIM design data | ||||
| Standard bucket | - | - | - | *2 |
| Tiltrotator | - | - | - | *2 |
| OPERA integration | ||||
| UDP / CAN API | - | - | - | *2 |
*1 Planned for 2026
*2 Planned for 2027
* This list may change without notice as development progresses and product specifications are revised.
How a deployment works
We review your site conditions, existing machines, communication environment and operating setup, then agree on the equipment specification, installation scope and the schedule to start of operation. If needed, we run a demonstration on a test machine. Depending on the conditions, demonstrations may be charged separately.
The system is installed at ARAV's assembly workshop or on site. It is a retrofit that does not touch the hydraulic system, so the machine can be returned to its original state. An in-house inspection checks the sensors, communication and safety functions.
After installation, we sign a purchase agreement for the equipment (remote-operation or automation unit) and a subscription agreement (monthly or annual) for the remote/autonomous operation application. Price, payment terms and maintenance scope follow what was agreed in the consultation.
The equipped machine is delivered and operation begins. The first year includes periodic maintenance support and operator training. Maintenance from the second year is agreed based on the operating record. After reviewing operating conditions and the site setup, we may not be able to accept every project.
These steps describe how projects run in Japan. For sites outside Japan, installation, operator training and maintenance arrangements are discussed with each customer before the project starts.
Considering RX Pro?
Tell us about your machines and site, and we will get back to you by email.